single nano relay (tht ?thr) pcb relays single relays catalog 1308028-2 revised 8-2009 all specifications subject to change. consult tyco electronics for latest specifications. 106 features smallest automotive pcb relay in its class: minimum pcb area required: 81 mm 2 dimensions: l x h x w (mm) 10.2 x 14.0 x 8 minimal height: 14.0 mm minimal weight first automotive relay using overmolding technology highest reliability due to overmolding process limiting continuous current 30 a very easy routing of pcb-layout power-saving high- impedance coil low noise operation wave (tht) and reflow (thr/pin-in-paste) solderable versions for twin version refer to nano relay typical applications car alarm door lock heated rear screen horn immobilizer interior lights seat control please contact tyco electronics for relay application support. design elv/rohs/weee compliant tht: sealed type washable thr: sealed type open vent hole weight approx. 4 g (0.14 oz.) nominal voltage 12 v terminals pcb terminals for assembly on printed circuit boards conditions all parametric, environmental and endurance tests are performed according to eia standard rs-407-a at standard test conditions unless otherwise noted: 23? ambient temperature, 20 - 50% rh, 998.9 ?3.9 hpa. for general storage and processing recommendations please refer to our application notes and especially to storage in the ?lossary page 23 or at http://relays.tycoelectronics.com/ appnotes/ 138_c-r1_3d1 disclaimer all technical performance data apply to the relay as such, specific conditions of the individual application are not considered. please always check the suitability of the relay for your intended purpose. we do not assume any responsibility or liability for not complying herewith. we recommend to com plete our questionnaire and to request our technical service. any responsibility for the application of the product remains with the customer only. all specifications a re subject to change without notification. all rights of tyco electronics are reserved.
single nano relay (tht ?thr) pcb relays single relays catalog 1308028-2 revised 8-2009 all specifications subject to change. consult tyco electronics for latest specifications. 107 138s_dd1 138s_vt2 138s_dd2 view of the terminals (bottom view) dimensional drawing * ) * ) additional tin tops max. 1 mm
single nano relay (tht ?thr) pcb relays single relays catalog 1308028-2 revised 8-2009 all specifications subject to change. consult tyco electronics for latest specifications. 108 contact data typical areas of application resistive/inductive load contact configuration 1 changeover contact / 1 form c circuit symbol (see also pin assignment) rated voltage 12 v rated current nc/no 15 a/20 a limiting continuous current 23? 25 a /30a 85? 15 a/20 a 105? 10 a/12 a contact material silver based max. switching voltage/power see load limit curve max. switching current 1) nc/no on 2) 30 a off 30 a min. recommended load 3) 1 a at 5 v voltage drop at 10 a (initial) for nc/no contacts typ. 30 mv, 300 mv max. mechanical endurance (without load) > 5 x 10 6 operations electrical endurance motor reverse blocked: at cyclic temperature ?0/+23/+85? > 10 5 operations and 13.5 v at 25 a, 0.77 mh inductive load 1) the values apply to a resistive or inductive load with suitable spark suppression and at maximum 13.5 v for 12 v load voltages. 2) for a load current duration of maximum 3 s for a make/break ratio of 1:10. 3) see chapter diagnostics of relays in our application notes page 31 or consult the internet at http://relays.tycoelectronics.com /appnotes/ load limit curve 10 100 110100 switching current [a] switching voltage [vdc] load limit curve 2 load limit curve 1 50w 100w 200w 400w 138s_llc1 load limit curve 1 ^ = arc extinguishes during transit time load limit curve 2 ^ = safe shutdown, no stationary arc 3 5 4
single nano relay (tht ?thr) pcb relays single relays catalog 1308028-2 revised 8-2009 all specifications subject to change. consult tyco electronics for latest specifications. 109 circuit diagram 1 changeover contact/1 form c coil data available for nominal voltages 12 v nominal power consumption of the unsuppressed coil at nominal voltage 0.8 w test voltage winding/contact 500 vac rms maximum ambient temperature range 1) ?0 to +105? operate time at nominal voltage typ. 3 ms release time at nominal voltage 2) typ. 1.5 ms 1) permanent use above 85? could be critical, see also operating voltage range diagram. 2) for unsuppressed relay coil. note: a low resistive suppression device in parallel to the relay coil increases the release time and reduces the lifetime caused by increased erosion and/or higher risk of contact tack welding. 12 4 3 5 138s_pa3 operating voltage range 0 5 10 15 20 25 30 -40 -20 0 20 40 60 80 100 120 ambient temperature [ c ] coil voltage [ v ] umax. uop. (e = un x 1.12) uop. (e = 0v) does not take into account the temperature rise due to the contact current e = pre-energization 138s_ovr1
single nano relay (tht ?thr) pcb relays single relays catalog 1308028-2 revised 8-2009 all specifications subject to change. consult tyco electronics for latest specifications. 110 part numbers (see table below for coil data) contact contact enclosure soldering relay description part number arrangement material technology v23138-c1005-a403 9-1414964-1 1 form c silver based sealed tht v23138-r1005-a403 1-1414960-7 1 form c silver based open vent hole thr coil versions ordering information coil data rated coil coil resistance must must allowable overdrive 1) for voltage ?0% operate voltage release voltage voltage (v) nano single (v) ( ) (v) (v) at 23? at 105? v23138-**005-**** 12 180 6.9 1.0 24 14.7 1) allowable overdrive is stated with no load applied and minimum coil resistance. standard delivery packs (orders in multiples of delivery pack) nano single: 2600 pieces environmental conditions temperature range, storage refer to storage in the ?lossary catalog page 23 or http://relays.tycoelectronics.com/appnotes/ test relevant standard testing as per dimension comments cold storage iec 68-2-1 1000 h ?0? dry heat iec 68-2-2 ba 1000 h 125? climatic cycling with condensation tht en iso 6988 20 cycles storage 8/16 h thermal change iec 68-2-14 nb 35 cycles ?0/+125? thermal shock iec 68-2-14 na 1000 cycles ?0/+125? dwell time 1 h damp heat cyclic tht iec 68-2-30 db, variant 2 6 cycles 40?/55 c/93% constant tht iec 68-2-3 method ca 56 days 40?/93% corrosive gas iec 68-2-42 10 days iec 68-2-43 10 days vibration resistance iec 68-2-6 (sine pulse form) 10 - 500 hz no change in the 6 g switching state > 10 s shock resistance iec 68-2-27 (half sine form single pulses) 6 ms no change in the up to 30 g switching state > 10 s solderability hot dip 5 s aging 3 (4 h/155?) tht iec 68-2-20 ta, method 1 215? for leaded process (tm = 183?) thr iec 68-2-58 245? for pb-free process (tm = 217?) resistance to soldering heat hot dip 10 s with thermal screen tht iec 68-2-20 ta, method 1a 260? thr iec 68-2-58 260? preheating min 130? sealing tht iec 68-2-17 qc, method 2 1 min/70? thr open vent hole
|
